• Standard Industrial is 100% Owned, Operated and Manufactured In The U.S.A.
• The model AM straight side press is perfect for full length forming at full tonnage as well as left to right and off-center loading at full tonnage via our extremely heavy duty gibbing system and enclosed end frame design. The model AM also allows front to back off-center loading within +,- 6" of the centerline of the bed. If off-center loading is required the entire front to back width of the bed then the model CM press should be considered. Contact the factory for details on the differences in these presses.
• The model AM straight side press is a more traditional style of straight side with much more left to right bed and ram area than the smaller bed DCSS presses however has a smaller price tag than the extremely heavy duty CM style presses. The AM is able to hold tolerance left to right much better than a direct hydraulic design due to its bellcrank linkage that gives the press full tonnage from one end of the press to the other.
• Our single cylinder design develops full tonnage anywhere along the bed left to right and front to back. The bellcrank linkage system is actuated with a single cylinder utilizing A660 bronze at the bearing points. These off the shelf material bearings are designed to withstand up to 6 times the machines overall tonnage and they are covered by our extensive 5 year parts warranty. The model AM is designed to accept virtually all forms of press applications whether it is punching, forming, blanking, coining, swedging, die tryout, trimming, drawing and so on. The AM is available up to 1,000 tons and particularly excels at progressive die set ups where you have varying amounts of tonnage being applied across the bed all in the same stroke.
• 100% made in the USA with our unmatched 5 year parts warranty plus a lifetime of readily available parts all from your local suppliers. You will never have another "orphaned" machine due to an overseas manufacturer who can’t get you parts or a domestic manufacturer with proprietary parts that forces you to buy everything from them. With Standard Industrial you will always be able to get the part you need for the lifetime of the machine from any number of sources available to you.
• 100% Made In the United States of America
• All Components Readily Available From Your Local Suppliers
• Hydraulic Oil cooler (fan radiator type)
• Two hand controls for operator safety
• ANSI B11.2 standards
• Magnetic starter with over and under voltage protection with disconnect switch
• JIC type electrical components in NEMA 12 enclosures
• 120 volt control circuit and 230-3-60 or 460-3-60 electrics through 40 h.p., for 50 h.p. and above 460 v. is standard
• Counterbalance valve & Decompression system for punching/bottoming
• Dependable Support from the people who make the machine
• Typical 20-30 Year Lifetime
• Hydraulic Tonnage Control
• Full Tonnage throughout Stroke
• (2) 5/8" t-slots in the bed and (2) 5/8" t-slots in the ram
• 5 Year Parts Warranty
• 5 Year Limited Onsite Labor Warranty
• Lifetime telephone support at no charge
• Front to back and left to right off-center loading capability via extremely heavy duty gibbing system and enclosed end frame design
• All steel, extremely heavy duty construction
• All electrics and hydraulics including oil filter are included as standard
• Simple mechanical limit switches to control open height, speed change point and lower limit actuated by 2 hand palm button control.
• Self-contained hydraulic system with oil cooler and filter
• T-slots in the bed and ram
• Two hand control station
• A counterbalance valve for punching and a decompression system for bottoming applications are standard equipment on all Standard Industrial presses
• Single cylinder drive system providing full tonnage the entire length of the bed and ram
• Adjustable shaft packing
• Tonnage control
• Completely adjustable open height, stroke and speed change point
• Extremely heavy duty welded frames
• APPLICATIONS:
• Embossing
• Drawing
• Stamping
• Die Try-out
• Sizing
• Rubber Pad Forming
• Forming
• Swedging
• Trimming
• Punching (Due to the overall weight of the ram and the drive system, when punching or blanking with a four column press, you should limit your overall tonnage to 50% unless stroke dampers are used.)
• Blanking (Due to the overall weight of the ram and the drive system, when punching or blanking with a four column press, you should limit your overall tonnage to 50% unless stroke dampers are used.)

Specifications are subject to change without notice.

NOTE: Data is provided by the manufacturer.

WARRANTY: 5 YEAR – STANDARD Parts & Limited Onsite Labor

• Optional AUTOMEC CNC Control
• Programmable logic controller (PLC) to control the base functions of the press including multiple job storage, stroke length, open height point, tonnage, decompression, ram delay/dwell at bottom of stroke (not under tonnage A mechanical standard to control limits of the press and is also included even with PLC.
  
• Light curtain safety barrier system provides infra-red beam during operation and shuts machi Base op front of press only-other optional curtains can be quoted per customer specification.
• Interlocking side barriers as physical barriers-can be used in conjunction with light curtains or alone
• Special single color paint
• Dwell under tonnage sustains desired tonnage for a set amount of time - typically used for manufacturers of plastics or fiberglass products
• Custom or special controls per user specifications
• Remote auto cycle for automated operations
• Special machining of bed and/or ram
• Removable bolster plates for bed
• Die cushions for drawing and/or part ejection
• Ejector cylinders for drops or parts
• Scrap chutes or knockouts to remove drops or parts
• Stroke dampers for punching or blanking operations allow more overall dimensions to increase
• Quick change tooling components such as air actuated die lifters and/or power die removal systems-increase productivity by decreasing die change and set-up time
• High speed or special hydraulic systems
• T-slots in bed and ram (2 are standard in bed and ram)
• Automatic lubrication systems to decrease maintenance operations
• Safety gear lock systems with interlocking posts provide even more operator safety (Model AP only)
• Additional open height (NOTE: Does not automatically increase stroke length)
• Additional stroke for Model AP Four column press
  (NOTE: Does not automatically increase open height)
• Low speed retract allows the ram to return slower than normal
• Pressure ram reversal allows the ram to return when a particular pressure is achieved.
• Ram delay at bottom of stroke (not under tonnage)
• Coil line processing and material feeding equipment
• Custom and standard die sets
• The model AM, DC and DCSS can have longer open heights but are limited to a maximum of 12" stroke as an option
• The model AM is available in longer lengths but not shorter lengths
• W-Technologies stroke dampers allow more punching and blanking capacity without harming hydraulic system