Cart is empty
- Description
- Machine Capacity: w 36" x h 13" (915mm x 330mm)
- Production Level: Medium/Intermediate
- Speed: High-Speed
- Standard features: 5 Hp Drive Motor, Work Light, Chip Blower and Post Elevating Hand Wheel
- Take all of the features and benefits of the 36XX Series of DoALL band saws and turn it up a notch with a higher-speed cutting rate for volume production applications.
- The DoALL 3613-V5 high speed, vertical contour band saw features a variable frequency 5 hp (3.75 kW) AC inverter drive controls that start the motion of the band wheels slowly to reduce mechanical shock and increase drive train life. As an additional safety feature for the operator, a dynamic braking function rapidly stops blade motion when power is shut-off – reducing kickback from materials and injury from the band saw blade.
- The 3613-V5 medium production, upright metal cutting band saw is widely used in locations that cut a large variety of materials in one production day. The 3613-V5 can also be used for plastics, wood and other materials – making it a flexible “work horse” for facilities that demand only the best finished products.
- Column Mounted Controls-Column mounted controls give the operator easy access to band start and blade speed insuring their hands are away from the blade at band start.
- Variable Frequency Band Drive-Band drive is comprised of an electric variable frequency drive controlled motor transferring power thru our time honored, gear driven, 2 speed transmission giving maximum torque to the tooth tips of the sawblade reducing band stall and tooth strippage.
- Post Elevating Handwheel-Easy to operate post elevating handwheel allows the operator to keep the upper saw guide block as close to the top of the material being cut without getting their hands close to the blade during adjustment. Proper positioning minimizes the possibility of band deflection increasing band life and safety.
- Bandwheels-Cast aluminum, crowned bandwheels, are supplied with rubber tires to minimize wheel wear and insure proper band tracking. The tires allow for minimum damage to the set of your saw band.
- Manual Band Tension-Proper blade tension is manually set to a factory installed indicator which covers all widths of saw bands. This indicator will prevent the possibility of over/under tightening of the sawband for maximum cutting rates and extended band life.
- High Band Speeds-The machine's 5hp band motor and high-speed spindle allow for maximum cutting rates at higher speeds while sawing non-ferrous materials such as aluminum, plastics, wood, and rubber.
- Wheel Brush-the surface of the lower wheel minimizing damage to the lower wheel tire by reducing any chip buildup which may cause improper blade tracking.
- Saw Guide-Machine is equipped with one set of DoALL invented chevron type saw guide blocks and inserts which will handle 1/8-1/2” sawbands. These will allow proper support to the side and back of the band minimizing deflection due to overfeed conditions.
- Safety Systems-Band door interlocks prevent the starting of the saw band while the doors are open. They will also stop the band drive if the doors open during operation which protects the operator from being exposed to a moving band.
- 10 year manufacturer’s warranty available (DoALL Cut Above 10 Year Warranty Annual Investment).
- Table tilt to 45 degrees negative - 10 degrees positive.
- 20" Aluminum bandwheels with crowned rubber tires.
- Upper wheel adjustment 3"
- Operator controls mounted on column.
- One set of high speed, insert type guide blocks for bands 1/8" to 1/2"
- Band wheel brush
- Variable frequency band drive.
- Work light
- Manual band tension with indicator.
- Post elevating hand wheel.
- Chip box
- Chip blower (plant air required)
- Saw blade guards.
- Band door interlocks.
- Operation and parts manuals on USB stick.
- Recommended job selector
- One (1) complimentary DoALL Bi Metal saw blade.
- Insert setting gages with wrench and trunnion wrench
- Manufacturer
- Specifications
- Options/Accessories
- Secondary Table 17" x 19"
- 12" Travel glide table with (2) point safety buttons on the handles for blade start
- 18" Travel glide table with (2) point safety buttons on the handles for blade start
- Work holding vise to fit table "T" slots (Must use option A , B, or D)
- Extended traverse work table: 1100 lb. capacity, four (4) 2" T-Slots, 34 x 42" table area, reduces work height by approximately 4
- DBW-15 welder with grinder, column mounted, for 240 volts and below
- DBW-15 welder with grinder, column mounted, for 460 volt
- Extended work height 6 inch increments - Call for quote
- Work holding jaw with handles
- Band mist lubricator-80 psi plant air required
- Standard rip fence that attaches to 26 x 26" table
- No. 2 standard cut-off and mitering attachment for 26 x 26" table
- Disk cutting attachment - Capacity 2-1/2 - 30" diameter
- Magnetic wand chip remover
- High-speed guide blocks for bands 1/8" to 1/2" (1.5 - 13 mm), speeds to 6,000 fpm (1,830 m/min) less inserts (per pair
- Heavy-duty (high-speed) saw guide blocks for bands 1/8" to 1/2" (1.5 - 13 mm), speeds to 6,000 fpm (1,830 m/min) less inserts (per pair)
- Heavy-duty (high-speed) saw guide blocks for bands 5/8" to 3/4" (16 - 19mm), speeds to 6,000 fpm (1,830 m/min) less inserts (per pair)
- Heavy-duty (high-speed) saw guide blocks for 1" (27 mm) band, speeds 6,000 fpm (1,830 m/min) less inserts (per pair)
- Heavy-duty (high-speed) saw guide blocks with carbide-faced backup for bands 1/8" to 1/2" (1.5 - 13 mm), speeds to 6,000 fpm (1,830 m/min) less inserts (per pair)
- Heavy-duty (high-speed) saw guide blocks with carbide-faced backup bearings for 5/8" and 3/4" (16 and 19 mm) bands, speeds to 6,000 fpm (1,830 m/min) less inserts (per pair)
- Heavy-duty (high-speed) saw guide blocks with carbide-faced backup bearings for 1" (27 mm) bands only, speeds to 6,000 fpm (1,830 m/min) less inserts (per pair)
- Additional set of hardened tool steel reversible saw guide inserts (set of 4) for any single band width:
- 1/8" (3 mm)
- 3/16" (5 mm)
- 1/4" (6 mm)
- 3/8" (10 mm)
- 1/2" (13 mm)
- 5/8" (16 mm)
- 3/4" (19mm)
- 1" (27 mm)
- Optional tungsten-carbide, single-faced saw guide inserts (set of 4) for any single band width:
- 1/4" (6 mm)
- 3/8" (10 mm)
- 1/2" (13 mm)
- 5/8" (16 mm)
- 3/4" (19 mm)
- 1" (27 mm)
- Type I high-speed roller guide blocks, less rollers (per pair)
- 1/4" (6 mm)
- 3/8" (9 mm)
- 1/2" (13 mm)
- Type II high-speed roller saw guide blocks, less rollers (per pair) reduces work height 1" (27 mm) and restricts table tilt to 27°
- Set of Type II rollers for band saw width: (**Must purchase block MM above)
- 1/4" (6 mm)
- 3/8" (9 mm)
- 1/2" (13 mm)
- 5/8" (16 mm)
- 3/4" (19 mm)
- 1" (27 mm)
- Additional USB stick of manuals
- A Nationally Recognized Testing Laboratory (NRTL) is an independent third-part laboratory recognized by the United States Occupational Safety and Health Administration (OSHA) to test and certify products to applicable product safety standards
- Five (5) hours installation and operator training
- DoALL Cut Above 10 Year Warranty Annual Investment
- Custom Freight
DoALL 36 x 13 inch High Speed Vertical Contour Band Saw 3613-V5
STANDARD EQUIPMENT:
ITEM: 36" x 13" High Speed Vertical Contour Band Saw
MANUFACTURER: DoALL
MODEL: 3613-V5
Manufacturer:
DoALL
Machine Type
Machine Category:
Saws
Machine Sub-Category:
Contour
Position:
Vertical
Metalworking
Saw Capacity:
36"+
MODEL
|
3613-V5 |
|
Machine Capacity |
w 36" x h 13" (915mm x 330mm) |
|
Production Level |
Low |
|
Unitized Frame |
Arc-welded steel |
|
Throat, Band to Column |
36" (915mm) |
|
Maximum Work Height |
13" (330mm) |
|
Band Width Capacity |
1/16" to 1" (1.5mm to 27mm) |
|
Saw Band Length |
199" (5,055mm) |
|
File Band Length |
198" (4,950mm) |
|
Wheels |
Aluminum with crowned rubber tires |
|
Band Drive Motor |
5 hp (3.75kW) |
|
Variable Band Speed |
550 to 5,500 fpm (170 to 1,625 m/min) |
|
Table Height, Table to Floor |
40" (1,000mm) |
|
Table |
26" x 26" (660mm x 660mm), tilt 45° right and 10° left |
|
Coolant System |
Mist Lubricator Optional |
|
Upper Wheel Adjustment |
2" (75mm) |
|
Floor Space Dimensions |
W x L X H |
39" x 81" x 82" |
Material Pass Height |
39" |
|
Machine Weight |
1,550 lbs. |
|
Electrical |
Voltage Requirement 208V, 230V or 460V-60Hz-3ph Wye configuration (Must Specify at Order Placement) |
|
Total Amp Draw |
(FLA) 10.7(208) 10.7(230)5.3(460)Amps |
|
Height, Maximum |
82" (2,050mm) |
|
Floor Area |
39” x 80.5" (990mm x 2,045mm) |
|
Color |
DoALL blue (RAL Color#: 5012) |
|
Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts
