DoALL 24 inch Dual Column CNC Tube Band Saw TDC-400CNC

• Machine Capacity: w 16” x h 16" (400mm x 400mm)
• Machine Capacity Round Tube: 16" (400mm)
• Production Level: Extreme
• Standard Features: Mitsubishi Automatic Controls, Work Height Sensors and Variable Vise Pressure Control
• The DoALL TDC-400CNC is a highly efficient hydraulically controlled band-saw with multiple material feed. It is equipped with a programmable digital Mitsubishi controller, so the blade, as well as the indexer movement, is fully automated. The operator simply programs the required specifications and can begin cutting, with minimal interaction with the saw.
• If you’re a primary metal center, piping or oil and gas contractor looking to cut round tubes and pipe at a high production rate, the DoALL TDC-400CNC is an excellent choice. Nesting and auto indexing means you can load up multiple pieces of metal stock and cut at an increased speed.
• The blade is sloped 7 degrees to cutting table, which enables better performance during cutting of profiles as well as full materials – this improves blade life
• Operator Control Console
  The operator control console is mounted at the front of the machine. Its placement insures the operator’s safety by keeping their hands clear of the sawband at band start
• Mitsubishi Touch Screen Panel
  The colored touch screen control panel displays the cutting cycle indicator, blade tension warning, BRP (overfeed protection) function, band speed, band drive amp load, and a list of error messages allowing the operator to monitor all machine functions.
• Direct Driven Band Drive
  Drive is comprised of an electric VFD controlled motor transferring power thru a gear reduction unit directly to the drive wheel eliminating belt slippage giving positive torque to the sawblade.
• Automatic Cycle
  The Automatic Cycle function allows the operator the ability to write and save 20 programs containing 15 different lengths of parts eliminating the need to stop the cycle and reset for multiple part sizes of the same material saving production time.
• Automatic Overload Feed Protection
  BRP function monitors the band drive motor amperage stopping head fall when the operator set parameter is reached signaling an overfeed condition or a dull saw band.
• Nesting Fixtures
  Plug-n-play vertical hold-down clamp assemblies allow the operator to perform multiple pieces cutting increasing productivity.
• Hydraulic Clamping Vice
  Full stroke hydraulic vices combined with a split front vice will minimize set up time and maximize clamping pressure eliminating material movement and tooth strippage.
• Floating Indexer
  The vice carriage is guided with two rails and is hydraulically positioned by use of a DRO insuring accuracy and repeatability. The indexer “floats” allowing for lateral movement to clear crooked stock conditions so material is not dragged or scored during operations. The indexer is also capable of incremental indexing saving cycle time when in short part length operations increasing production.
• Hydraulic Band Tension
  Eliminates the possibility of over/under tightening of the band for maximum cutting rates and saw band life.
• Saw Head Design
  The saw head is mounted on linear rails which are mounted to two robust columns at a 7 degree cant. The 4 point head mounting system to the columns increases the stability of the saw head allowing for increased blade life.
• Band Brush
  Driven Band brush removes the chips from the blade gullets which would prevent the blade from attaining maximum cutting rates and blade life.
• Warranty
  One year parts and service subject to the terms and conditions listed on the last page.
  Optional ten year warranty is available (DoALL Cut Above 10 Year Warranty)

STANDARD EQUIPMENT:

• Programable logic controller for all machine functions.
• Automatic & semi-automatic cycle.
• Mitsubishi controller.
• Rapid head down approach.
• Carbide faced saw guide inserts with lead in bearings.
• Material Height Sensor.
• Full stroke hydraulic vises.
• Driven band cleaning brush.
• Infinite band speed by variable frequency drive.
• Automatic movable guide arm setting.
• Cast steel band wheels.
• Programable over feed protection.
• Vertical hold downs.
• Laser line generator.
• Feed rate/feed force saw head control.
• Mist band lubricator system.
• Normal and incremental indexing.
• Variable Vise Pressure.
• LED work light.
• 7 degree cant design.
• Saw blade guards.
• Auger style chip conveyor.
• Band door interlocks.
• Operation and parts manuals on USB stick.
• Recommended band speed chart.
• One (1) complimentary DoALL Bi Metal saw blade.
• Complimentary DoALL Cutting Fluids package